View previous topic :: View next topic |
Author |
Message |
isobars
Joined: 12 Dec 1999 Posts: 20936
|
Posted: Sun Oct 28, 2012 1:29 pm Post subject: |
|
|
speedysailor wrote: | Brake fluid will take paint off like no tomorrow, but I have never used it except on a matrix of cement. |
I know an auto painter who "repossessed" a full custom van paint job with brake fluid after the customer stiffed him, sneering, "What're you gonna do ... repo the paint job?" The customer came out the next morning to find his paint job on his driveway.
Works wonders on a car whose owner dinged your door and walked away, too. |
|
Back to top |
|
|
mchaco1
Joined: 08 Sep 2010 Posts: 645
|
Posted: Sun Oct 28, 2012 1:55 pm Post subject: |
|
|
gobbdogg wrote: | Chemicals aren't my first choice either- but the poster seemed wary of mechanical means- my first choice would be a sharp scraper- but it takes a practiced hand. I wanted to make the point though that solvents do not touch cured epoxy- at least in my 30 years of working with it I haven't found one that does. And sanding paint and finish has it's own drawbacks with toxic dust and the possibility of going deeper than intended. |
yeah, its not an even factory paint job that I can knock down and paint over.. its a thick brushed on job with clear over it that is full of bubbles and high spots. It has to come off or it will continue chipping off and take the new paint with it. Once I hit fiberglass its hard to tell if im taking it off while I scrub away at the paint with sandpaper. I already got a thin spot on the tail that leaked a bit from knocking it down to a sailable finish after I got it, so a decent stripper that wont hurt the epoxy would be best. |
|
Back to top |
|
|
mchaco1
Joined: 08 Sep 2010 Posts: 645
|
Posted: Sun Oct 28, 2012 1:55 pm Post subject: |
|
|
gobbdogg wrote: | Solvents will not affect the epoxy- use chemical stripper and rags...just be sure to clean thoroughly after- soap and water then alcohol which removes any trace of water- then repaint. |
any specific stripper? |
|
Back to top |
|
|
DanWeiss
Joined: 24 Jun 2008 Posts: 2296 Location: Connecticut, USA
|
Posted: Sun Oct 28, 2012 2:20 pm Post subject: |
|
|
Chemicals suck. The best way to take down that paint is with aggressive grit sanding, progressively finer. You won't do damage to the rocker as long as you sand down to the primer and then stop. You might see a beige filler in spots. That's OK, just avoid sanding that, tack cloth to remove all traces of grease and dust, then respray with primer and paint as best you see fit. _________________ Support Your Sport. Join US Windsurfing!
www.USWindsurfing.org |
|
Back to top |
|
|
isobars
Joined: 12 Dec 1999 Posts: 20936
|
Posted: Sun Oct 28, 2012 2:54 pm Post subject: |
|
|
mchaco1 wrote: | its a thick brushed on job with clear over it that is full of bubbles and high spots ... |
Holy crap! I'm starting to lean towards suggesting shag carpeting tip to tail. (If you try that, publish some pics. I gotta see that.) |
|
Back to top |
|
|
gobbdogg
Joined: 28 Sep 2008 Posts: 163
|
Posted: Sun Oct 28, 2012 4:06 pm Post subject: |
|
|
Off the shelf gel type- they all have the same basic chemicals- don't forget, paint and finishes are chemical suspensions/ emulsions too. |
|
Back to top |
|
|
isobars
Joined: 12 Dec 1999 Posts: 20936
|
Posted: Sun Oct 28, 2012 4:29 pm Post subject: |
|
|
Tip: when I'm working with stinky or risky chemicals, I do it outdoors in a breeze and make a point of keeping my face upwind. The solution to pollution is dilution.
And near Hanford, what the hell? |
|
Back to top |
|
|
mchaco1
Joined: 08 Sep 2010 Posts: 645
|
Posted: Sun Oct 28, 2012 5:56 pm Post subject: |
|
|
isobars wrote: | mchaco1 wrote: | its a thick brushed on job with clear over it that is full of bubbles and high spots ... |
Holy crap! I'm starting to lean towards suggesting shag carpeting tip to tail. (If you try that, publish some pics. I gotta see that.) |
Its not (quite) as bad as it sounds...the repair under is solid and the board is still super light. Its a fairly new board, so I want to get rid of the roughness and make it look at least decent, with some graphics. The biggest problem is the clear. I deceided to just go with sanding and do the best I can with it. Hopefully filing in the chips and using a good primer will keep it from chipping as much as it was. |
|
Back to top |
|
|
swchandler
Joined: 08 Nov 1993 Posts: 10588
|
Posted: Sun Oct 28, 2012 6:49 pm Post subject: |
|
|
"tack cloth to remove all traces of grease and dust"
On many of my polyurethane finish jobs that I been doing on wood projects, I'm a firm believer in using a tack cloth. However, using a tack cloth on jobs using resins, I've found that can totally ruin your finishing work. Instead of a tack cloth, I would use acetone, or at minimum, use soapy water followed by clean water using a sponge.
Another thing to keep in mind is using 3M White Acrylic Marine Putty as a fairing material to fill shallow pits, voids and scratches. It sands beautifully and accepts paint very well. Needless to say though, if you are trying to maintain underlying painted graphics, it's not the answer. |
|
Back to top |
|
|
mchaco1
Joined: 08 Sep 2010 Posts: 645
|
Posted: Sun Oct 28, 2012 8:27 pm Post subject: |
|
|
is it ok to use auto glazing putty? The marine stuff is a bit pricey for what im doing...but not worth using auto stuff if it wont hold up. |
|
Back to top |
|
|
|