View previous topic :: View next topic |
Author |
Message |
sundowner
Joined: 30 Sep 2015 Posts: 81
|
Posted: Mon Apr 14, 2008 4:16 pm Post subject: mast extension stuck in mast! |
|
|
This damn thing wont come out. So far I've bounced on it and had someone turn and pull one way while I turned and pulled the other way. It's really jammed, any tips? |
|
Back to top |
|
|
jp5
Joined: 19 May 1998 Posts: 3394 Location: OnUr6
|
Posted: Mon Apr 14, 2008 4:33 pm Post subject: |
|
|
Fill the mast up with water and let it sit in the hot sun for a couple of hours. Then get a rubber mallet and beat it out. If you can put a screw driver in the extension and beat it with the mallet so that it twists loose in the mast then use the mallet to strike directly outward on the extension driving it out. This is a regular occurence for me. |
|
Back to top |
|
|
bred2shred
Joined: 02 May 2000 Posts: 989 Location: Jersey Shore
|
Posted: Mon Apr 14, 2008 5:43 pm Post subject: |
|
|
The water trick can work if the bottom of your mast doesn't have a plug in it. I'd stay away from screwdrivers- that's a quick way to gouge your expensive mast.
The technique that always works for me is flex the joint (a lot) and get more people. Three or more people per side pretty much always gets the mast apart (assuming they're all turning the right way). Much better for the mast than using a screwdriver and better than trying to use boom heads.
The last tip, something I recently started doing, is to use electrical tape on the mast joint. It really helps keep sand out.
sm |
|
Back to top |
|
|
gboehm
Joined: 26 Mar 1995 Posts: 4
|
Posted: Mon Apr 14, 2008 6:16 pm Post subject: unsticking mast with pressure washer |
|
|
Needless to say, this has happened to me so many times I've lost count. I have always attached 2 booms - one on either side of the joint, and used the leverage to twist the two sections in opposite directions.
Always worked till one time it just didn't. After about a year of trying various things, I finally came up with the ultimate solution - a pressure washer. Just direct the stream at the joint - washes the sand out and works like a charm. If you don't have one, I imagine the wand at a car wash might work (it isn't nearly as powerful as the pressure washer, though). |
|
Back to top |
|
|
psmith2004
Joined: 06 May 2004 Posts: 90
|
Posted: Tue Apr 15, 2008 2:19 pm Post subject: |
|
|
I assume the downhaul line is still attached to the extension?
Find a cooperative tree and tie the free end of the line around the trunk of the tree ( use a bowline knot) and then give it a few sharp tugs. The extension should come out without too much trouble.
Peter |
|
Back to top |
|
|
drysuit2
Joined: 01 Apr 1997 Posts: 119
|
Posted: Sun Apr 20, 2008 9:12 am Post subject: |
|
|
Use the two boom method as described by others. But if it is really stuck, fill the inside mast extension with ice cubes. Stop it up with a plastic bag or something. Then heat the out side of the mast at the base with a blow dryer. The melting ice will cool, and contract the mast base, [works especially well with aluminum. But I’ve done this with carbon as well] the heat will expand the mast. Use the booms to apply a gentle twisting force. Do not jam a screwdriver anywhere or bang any thing. Carbon is very expensive and does not respond well to blunt force trauma. |
|
Back to top |
|
|
theq
Joined: 10 Apr 2000 Posts: 707
|
Posted: Sun Apr 20, 2008 11:26 am Post subject: |
|
|
I've seen most of those techniques suggested work one time or another. Since it's your extension that's stuck in the mast, you probably won't get much flex at the joint the way you can with a stuck mast ferrule.
You can get extra torque strength by using a downhaul crank tool as a lever. Just place it in the base, get someone else to hold the mast from twisting (perhaps with a boom attached), stick the crank-tool handle out for maximum leverage (Using like star lug wrench, "T" handle), and give it a twist. Good luck. |
|
Back to top |
|
|
speedysailor
Joined: 11 Sep 2007 Posts: 841
|
Posted: Thu Apr 24, 2008 6:40 am Post subject: |
|
|
bred2shred wrote: |
The last tip, something I recently started doing, is to use electrical tape on the mast joint. It really helps keep sand out.
sm | I tape my two piece booms together and the carbon X-C extention onto the North drop shape, but I don't find it necessary to tape the adjustable length extentions to the mast. Basically, you have to exercise good hygene and keep your componenents clean. In this way it isn't an issue. I will stuff a rag into the end of both the mast and extention when moving them around on the beach. The rag often doesn't come out until I'm ready to mount the rig to the board. If I forget the rag sometimes I do get sand in the mast. Consequently, I will always inspect it and wash it out if this is needed. In fact, I wash and inspect any mast or extention I use after every session. By the way, there was a young sailor at the beach yesterday who told me he had the problem. I should have recommended this thread, but didn't know where I saw it. I decided to read it and hope I see the guy again. The ice cube/hair dryer trick, although time consuming, seems like the best way if all else fails. I wasn't aware of it. However, I did see an article in an old Windsurfing Mag that covered the other alternatives. |
|
Back to top |
|
|
btbill
Joined: 05 Jun 2002 Posts: 236
|
Posted: Thu Apr 24, 2008 8:03 am Post subject: |
|
|
If its the mast extension that is stuck in the bottom of the mast, try a rubber mallet. Lay the mast on a flat surface such as the open tail gate of a pickup, hold the mast with one hand, and bang the extension "away from you" on the pulleys/grommets. Once it is freed enough to turn, then work it out by hand. Only use a rubber mallet to avoid damaging the extension. Note that the mallet will get chewed up, but I keep one in my gear box just for that purpose. Works every time, especially living here in Hatteras where sand sticks everything together!
Good Luck!
Bill
www.obxbeachlife.com
www.obxloopfest.com |
|
Back to top |
|
|
sundowner
Joined: 30 Sep 2015 Posts: 81
|
Posted: Fri Apr 25, 2008 3:25 pm Post subject: |
|
|
Thanks for the mallet suggestion bill. Worked like a charm. Hey bruce, by chance did that young windsurfer have a dark complexion and drive a blue jeep with a mistral sticker on the back? |
|
Back to top |
|
|
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum You can attach files in this forum You can download files in this forum
|
|
|