myiW Current Conditions and Forecasts Community Forums Buy and Sell Services
 
Hi guest · myAccount · Log in
 SearchSearch   ProfileProfile   Log in to check your private messagesLog in to check your private messages   RegisterRegister 
Yet another winter Board conversion project TABOU Rocket
Goto page 1, 2, 3  Next
 
Post new topic   Reply to topic    iWindsurf Community Forum Index -> Windsurfing Discussion
View previous topic :: View next topic  
Author Message
U2U2U2



Joined: 06 Jul 2001
Posts: 5467
Location: Shipsterns Bluff, Tasmania. Colorado

PostPosted: Thu Jan 26, 2012 4:08 pm    Post subject: Yet another winter Board conversion project TABOU Rocket Reply with quote

A short background paragraph, I wanted a board with less fin length to use in my granite rock strewn lake in Maine. I had the option of spending big bucks on a ready made twin , or find a donor board to cut up.

If you have followed any of my previous winter projects you know which path I have taken.

the board is a 2011 TABOU Rocket 135L. I made a decision to do a 2+ 1 instead of twin based mostly on the fins I already have.
To do this as a twin I would use slot boxes , and I would need a pair of large slot box twins .

Since I have a huge arsenal of side bites and the weight gain would be minimal using my tried TRUE and tested ProBox, it was a 2+1 that won out.

The placement of the boxes is typical 2 + 1, instead of thruster placement, so further forward from the tail. This should present a firm ride with drawn out speedy turns. The intent IN the first photo, large center and small sides. As a option it can/should/ hopefully should be a little more turny in the fin set up in photo 2, which is larger sides and smaller center. So that will mitigate the 2+ 1 setup, some, and of course part of the fun is to see which works best, or put another way, which I like best.
It may very well be a compromise of size that makes the most pleasing overall ride.
I did not want or expect to change to character of this semi large free ride board by this addition, or fin change.The sole intend was to have fins that didn't luv the rocks so much.

This was an easy project, I only added the red ribbon as a graphic.

for the geeks there: the toe is 1.98 degrees toward the nose, the 2nd photo have custom G10s, with a very sophisticated inside 70/30 foil , all the sides fins are ProBox fins.

Breaking water will be OBX in April, anyone is welcome to try it.










next project is a quadster, using slot box and Black Project Fins

_________________
K4 fins
4Boards....May the fours be with you

http://www.k4fins.com/fins.html
http://4boards.co.uk/
Back to top
View user's profile Send private message
LeeD



Joined: 12 Jun 2008
Posts: 1175

PostPosted: Thu Jan 26, 2012 11:30 pm    Post subject: Reply with quote

I'd reco the G-10 side biters.
Softpoly clear cheaps tend to spin out and never regrab.
I think tris, you need more total fin area than a big single blade.
Hope it works.
Back to top
View user's profile Send private message
U2U2U2



Joined: 06 Jul 2001
Posts: 5467
Location: Shipsterns Bluff, Tasmania. Colorado

PostPosted: Fri Jan 27, 2012 1:46 am    Post subject: Reply with quote

for a 2+1 or tri fin the area should be 1.33--1.5 times greater than the single fin.

in this case the sides need to have around 100cm2 of area with the black G10 fin in the first photo. so around 11cm

the 2nd set has a smaller center, so the sides should be a little larger

it depends quite a lot on the fin shape for the area.

_________________
K4 fins
4Boards....May the fours be with you

http://www.k4fins.com/fins.html
http://4boards.co.uk/
Back to top
View user's profile Send private message
SeaDawg



Joined: 12 Sep 2002
Posts: 384

PostPosted: Fri Jan 27, 2012 7:19 am    Post subject: Reply with quote

I have the same board and sail it in Hatteras often. The fin I use most often is true ames 11in surf grass. Looks like you did a pro job on your project:-)
Back to top
View user's profile Send private message
U2U2U2



Joined: 06 Jul 2001
Posts: 5467
Location: Shipsterns Bluff, Tasmania. Colorado

PostPosted: Fri Jan 27, 2012 9:50 am    Post subject: Reply with quote

the Makani fin, 1st photo is 28cm, so 11". the MUF is 24cm , but area quite a lot smaller. OTOH I do have the True Ames in 24cm...ummmm

I would have thought that a bit on the small side..what size sails do you use ?

Thanks, think it will come together nicely

_________________
K4 fins
4Boards....May the fours be with you

http://www.k4fins.com/fins.html
http://4boards.co.uk/
Back to top
View user's profile Send private message
SeaDawg



Joined: 12 Sep 2002
Posts: 384

PostPosted: Fri Jan 27, 2012 10:15 am    Post subject: Reply with quote

The 11in handles my 7.2 Ezzy Infinity very nicely, also my 6.5 Infinity. I have the same fin in 10in which I use with my 5.2 Ezzy Wave SE.

I sort of bought into the theory that multi fins produce more drag and that it was more important to find a well shaped single fin.


Fins are a such a huge debate, I have 15 yr old tuttle weed(the blue ones) that still work well.

I've gotten so used to the Wardog/SurfGrass I use them even when there are no weeds. Up wind,manuverability/speed are more than adequit for my sailing needs.
Back to top
View user's profile Send private message
U2U2U2



Joined: 06 Jul 2001
Posts: 5467
Location: Shipsterns Bluff, Tasmania. Colorado

PostPosted: Fri Jan 27, 2012 10:35 am    Post subject: Reply with quote

SeaDawg wrote:
The 11in handles my 7.2 Ezzy Infinity very nicely, also my 6.5 Infinity. I have the same fin in 10in which I use with my 5.2 Ezzy Wave SE.

I sort of bought into the theory that multi fins produce more drag and that it was more important to find a well shaped single fin.


Fins are a such a huge debate, I have 15 yr old tuttle weed(the blue ones) that still work well.

I've gotten so used to the Wardog/SurfGrass I use them even when there are no weeds. Up wind,manuverability/speed are more than adequit for my sailing needs.


I chose the weed fin because it has a shorter draft length , so less depth to encounter rocks. I use weed fins when I have to, otherwise I find they turning ability lacking, several exceptions and shapes come closer to a regular fin.

my multi fin philosophy is that they will increase drag, but the other positive characteristics more than off set that, and if you like or need upwind capability then a good tri fin will really make you smile.

This board was NOT about multi fin , but rather a solution to a performance board want/need with a shorter fin depth.

I fully intend to exploit the 3 fins to see how far it goes on the Rocket,
I will be really happy if its as good as the single, but quietly hoping for more

_________________
K4 fins
4Boards....May the fours be with you

http://www.k4fins.com/fins.html
http://4boards.co.uk/
Back to top
View user's profile Send private message
SeaDawg



Joined: 12 Sep 2002
Posts: 384

PostPosted: Fri Jan 27, 2012 11:11 am    Post subject: Reply with quote

It's always best to keep those expensive fins off the rocks. I had a board back in the early 80's with a tri fin set up, but back then they were poly cabonate and twisted something fierce inducing massive spinout.

I'm sure your having fun expermenting, especially with lots of spare bits n' pieces laying around on long cold winter days.
Back to top
View user's profile Send private message
U2U2U2



Joined: 06 Jul 2001
Posts: 5467
Location: Shipsterns Bluff, Tasmania. Colorado

PostPosted: Fri Jan 27, 2012 11:36 am    Post subject: Reply with quote

I find that the short.. 4.5" fins are fine in fiberglass, so as sidebites their application is OK, some flex may be of benefit, depending on the fin setup/board, not so I think on this one.
Their are some fins that are a lessor grade of plastic, and those I can see being on the bendy side , translates into you get what you pay for.

another variation here, 24cm Makaini and 11.5cm sides in FCS very light weight
and high tech foils. Worked well on my AmiGiu conversion.


_________________
K4 fins
4Boards....May the fours be with you

http://www.k4fins.com/fins.html
http://4boards.co.uk/
Back to top
View user's profile Send private message
SeaDawg



Joined: 12 Sep 2002
Posts: 384

PostPosted: Fri Jan 27, 2012 10:27 pm    Post subject: Reply with quote

So, for example, it's blowin 20 or so south west at the hole in Avon. You take a run or two with a single fin and then ad the side fin, what does one set up vs. thr other do for you?
Back to top
View user's profile Send private message
Display posts from previous:   
Post new topic   Reply to topic    iWindsurf Community Forum Index -> Windsurfing Discussion All times are GMT - 5 Hours
Goto page 1, 2, 3  Next
Page 1 of 3

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You can attach files in this forum
You can download files in this forum

myiW | Weather | Community | Membership | Support | Log in
like us on facebook
© Copyright 1999-2007 WeatherFlow, Inc Contact Us Ad Marketplace

Powered by phpBB © 2001, 2005 phpBB Group