View previous topic :: View next topic |
Author |
Message |
btbill
Joined: 05 Jun 2002 Posts: 236
|
Posted: Fri Apr 19, 2013 8:07 pm Post subject: Windsurfing Board Request (redesign the vent screw head) |
|
|
Just thought of something while I was out solo today in the parking lot at Coquina Beach figuring out how to close a phillips head vent screw with a multi-tool that did not have a phillips head driver (in my haste to get out the door following a work meeting to go sailing (blowing S near 30mph all afternoon on the OBX today!), I forgot a phillips head screwdriver).
How about all vented windsurfing boards use a hex head that matches the size for a standard sail batten wrench?! Or perhaps a replacement vent plug could be offered that you could pay a few bucks for.
This way, only need the sail batten wrench tool that can be used for either the sail battens or board vent screw. Plus the hex head will not wear out like phillips head sometimes do, especially if you do not have the screwdriver in your truck!
thoughts?!
bb |
|
Back to top |
|
|
isobars
Joined: 12 Dec 1999 Posts: 20936
|
Posted: Fri Apr 19, 2013 8:18 pm Post subject: |
|
|
I haven't had a sail that used a batten screw since WAY last century, but I have at least 30 Phillips head screwdrivers. |
|
Back to top |
|
|
btbill
Joined: 05 Jun 2002 Posts: 236
|
Posted: Fri Apr 19, 2013 8:31 pm Post subject: |
|
|
hmmm, I get new wave sails every year and they always include batten wrench. |
|
Back to top |
|
|
wdsurf
Joined: 22 May 1999 Posts: 335
|
Posted: Fri Apr 19, 2013 9:03 pm Post subject: vent plug |
|
|
good idea. every sail bag i got has one |
|
Back to top |
|
|
dllee
Joined: 03 Jul 2009 Posts: 5329 Location: East Bay
|
Posted: Fri Apr 19, 2013 9:24 pm Post subject: |
|
|
Corner of your slotted screwdriver works just fine, as do some of your keys on your keyring. |
|
Back to top |
|
|
gregnw44
Joined: 23 Jul 2008 Posts: 783 Location: Seattle, Wa
|
Posted: Fri Apr 19, 2013 9:59 pm Post subject: |
|
|
Right. Very good tip from Zirt !!
But also... I agree with your idea.
Most the time, I don't have to worry about it... cause most of my sails, from the early 90's have webbing and plastic buckles to tighten battens (which takes me 15 seconds, each time I rig/de-rig)... no tool required.
But I also have a couple modern sails from the last 10 years. And yes, like you say... they have allen head screws to tighten the battens.
I don't know if "most" the sails that use these, also use the same size. But YES, if they did... it would simplify things to remember.
Greg - |
|
Back to top |
|
|
isobars
Joined: 12 Dec 1999 Posts: 20936
|
Posted: Sat Apr 20, 2013 7:54 am Post subject: |
|
|
isobars wrote: | I haven't had a sail that used a batten screw since WAY last century, but I have at least 30 Phillips head screwdrivers. |
I also haven't messed with a vent screw since way last century, when I'd drive over the Rockies @ >7,000 feet on my way to the OR coast. |
|
Back to top |
|
|
isobars
Joined: 12 Dec 1999 Posts: 20936
|
Posted: Sat Apr 20, 2013 7:59 am Post subject: |
|
|
gregnw44 wrote: | it would simplify things to remember. |
i gave up trying to remember things way last century, too.
Now I just keep everything in bags or milk crates for a quick, brainless getaway. For backup, on my refrigerator is a list of everything I take, right down to my car keys (so I won't have to waste a whole minute running back to grab them.) |
|
Back to top |
|
|
wdsurf
Joined: 22 May 1999 Posts: 335
|
Posted: Sat Apr 20, 2013 8:30 am Post subject: vent |
|
|
tool less option always works replace the slot/phillips screws with chinook thumb vent you grab it and turn it with your digits NO TOOLS |
|
Back to top |
|
|
BritishSteve
Joined: 18 Apr 1997 Posts: 17
|
Posted: Sat Apr 20, 2013 9:10 am Post subject: |
|
|
My battern screws are 10x24 SAE size so use a 5/32" hex wrench (4mm is also pretty compatable). You have not mentioned what thread your vent screw is, I have seen many different sizes. You can buy hex drive machine screws, obviously the size of the hex drive varies with the diameter of the machine screw. The chance of the machine screw with the correct thread having the correct hex drive is pretty slim. It's probably cheaper to buy a screwdriver with multiple bits and leave it in your vehicle. |
|
Back to top |
|
|
|